Poured liners
A cement based mix is poured around a form inside the chimney to create a smooth new flue and can add strength to older masonry.
A sweep in Shrewsbury can reline an unlined or damaged flue so smoke and gases vent safely from a fireplace, stove, insert, furnace or water heater. Call (732) 876-9672 to reach a local chimney sweep.
Inside most chimneys is a liner, the tube that actually carries smoke and flue gases to the top. Without one, heat and acidic condensation attack the masonry, and gaps can let heat or carbon monoxide escape into the home. In older houses, it is common to find an unlined chimney or a clay tile liner that has failed.
Relining usually comes up for one of a handful of reasons. Clay tiles crack after chimney fires, shift as the house settles and lose mortar at the joints, while some chimneys never had tiles to begin with. Installing an insert, stove or high efficiency furnace often means the old flue is the wrong size.
A camera scan of the flue shows the sweep the condition of the old liner and any offsets or obstructions. That reveals whether the existing tiles can be repaired or need to be replaced, and it shows the route a new liner will take. Seeing the inside of the flue makes the decision much easier.
Many chimney liner installation calls in Shrewsbury also turn up a need for chimney liner repair or chimney inspection.
Need chimney liner installation in Shrewsbury? Call (732) 876-9672 to talk to a local chimney sweep.
Call nowHere is how a sweep usually handles a liner installation.
A camera is run through the flue to check the existing tiles, offsets and obstructions. It decides between repair and relining.
The liner diameter is matched to the appliance outlet or the fireplace opening, following the manufacturer guidance. The full height of the flue is measured too.
The flue is swept and any loose tile or obstruction is cleared so the liner can pass. Tight flues sometimes need old tiles removed.
The stainless liner is lowered from the roof down to the appliance, often wrapped in an insulation blanket. Insulating it helps draft and reduces creosote and condensation.
At the top, a plate and cap close off the flue, and at the bottom the liner connects to the appliance. The connections keep gases from leaking into the old flue.
A draft test confirms the new liner is working. Keep carbon monoxide alarms on every level of the home.
A cement based mix is poured around a form inside the chimney to create a smooth new flue and can add strength to older masonry.
Liners can be insulated with a blanket or a poured mix where the system or chimney calls for it.
Flex liners snake through chimneys with bends and offsets and are common for inserts, stoves and gas appliances.
Smaller liners for gas or oil furnaces and water heaters stop condensation from damaging the chimney.
Straight flues can take rigid stainless pipe which suits wood burning appliances well.
Most relining jobs use stainless steel, which handles high heat and corrosive flue gases well. It comes in flexible coils for chimneys with bends and rigid sections for straight flues. The sweep picks a grade of stainless that suits the fuel the appliance burns.
Stainless liners are often paired with insulation, either a wrap or a poured mix, which keeps flue gases warm and can be required for clearance to combustibles. A cap and top plate finish the job at the top of the chimney. Many Shrewsbury chimneys get a stainless liner when an old fireplace is converted to an insert.
Chimney relining is the process of lining a flue again when the original liner is cracked, missing or unsuitable. Changing to an insert or stove, finding cracked tiles or recovering from a chimney fire usually leads to relining. In most cases the work is done from the top without tearing into the house.
Before relining, it helps to know which appliances share the chimney. A furnace replaced with a high efficiency model that vents through the wall can leave the water heater alone in an oversized flue, which leads to poor draft and condensation. A smaller liner brings the draft back where it should be.
Around Shrewsbury, relining usually comes up when a home changes heating appliances or an inspection turns up cracked tiles. From Shrewsbury out to places nearby like Little Silver, Red Bank, Oceanport and Eatontown, wood stoves and inserts are common, and each one needs a properly sized liner, which is why relining is one of the most common chimney upgrades in the area.
Need chimney liner installation around Shrewsbury? Call (732) 876-9672 for a Shrewsbury chimney sweep who serves the towns around it too.
Cold winters keep fireplaces, wood stoves and oil burners working for half the year or more. Masonry takes the worst of it from the freeze and thaw cycle: water soaks into brick, mortar joints and the crown on a mild day, freezes overnight and expands, which is how cracks, loose bricks and leaks start. Nor'easters drive rain sideways into flashing and mortar that looked fine in summer. That is why chimney cleaning in Shrewsbury is usually booked in the fall, before the first cold night.
Small chimney problems caught early usually stay small repairs.
Chimney sweeps in Shrewsbury know the chimneys and fireplaces common in local homes.
Ask your questions before you agree to anything.
More questions? Call (732) 876-9672
Restoring a damaged chimney liner with resurfacing, joint repair or partial replacement.
Learn moreA top to bottom check of the chimney, inside and outside so you know whether it is safe to light a fire.
Learn moreInstalling wood, gas and pellet inserts in existing fireplaces, with the chimney inspected before anything goes in.
Learn moreWood stove installation into an existing chimney or a new insulated chimney, so the stove drafts well and stays clear of anything that can burn.
Learn moreLooking for something else?
See all chimney servicesCall now for Shrewsbury chimney liner installation and help in the towns around it.
Free to call. No forms to fill out.